ALPI – Aluminum railing system
Railing system ALPI is an aluminum profile component railing system that is weatherproof and offers many possibilities for making different types of railings.
The following can be used as filler of the railing:
• Wood (board);
• Square or round metal tubes, both horizontally and vertically;
• Bent sheet metal, perforated sheet metal, etc.
The railing can be ordered with or without a handrail. It is also possible to install an additional handrail on the side of the railing (aluminum, stainless steel or wood).
The railing can be used on flat surfaces as well as on stairs and slopes.
The railing can also be used on curved surfaces.
The railing may be mounted on the side of the aperture with special fastening brackets or on a flat surface with a base.
Post size: 80 x 40mm
Fastening: on the front edge or on top
Installation: flat or sloping surfaces
Finish: powder coated (by RAL or other code)
Width of groove: 21mm
Max height of the post: 1450mm
Max distance between posts: 1200mm
Handrail: aluminum profile
Additional handrail: wood, aluminum, painted or
Mounting a post on a flat surface or at the front edge is done with special “fastening bases.”
They are fastened to the post with bolts and then mounted on the flat surface together with the post with screws or anchors.
No welding joints are needed.
Product range includes handrails of aluminum profile and wood (oak, birch, beech).
Handrail dimensions: 80 x 40mm.
Fastening with a hidden fastening system under the handrail.
Additional handrail on the side of the railing:
On the side of the additional handrail is either an aluminum profile or a wood (oak, birch, beech)
Dimensions Round with a diameter 40mm.
Filler of the railing:
There are several options for the filler of the ALPI railing.
Glass, plywood, perforated metal plates, grating filler, etc., may be used as a filler.
The filler may be over the edge of the post, even with the edge of the post, or below the edge of the post (in the versions with a handrail)
It is possible to use different types of perforation on the plates or cut/draw different shapes. In the case of grating, round or square rods horizontally, vertically or diagonally, etc.
Glass finishing according to the possibilities of the glass producers.
Perforated metal plates and grating fillers are finished with paint (powder paint in general) or varnish.
It is possible to order plywood filler oiled, lacquered, stained, etc.
Minimalist railing system GP
The GP glass railing system is a minimalist glass railing system without posts suitable for indoor and outdoor use. Does not contain metal parts, is rustproof and waterproof.
Finishing options are almost endless. If looks of the aluminum itself is not suitable, it can be painted with powder paint over the entire spectrum of the RAL catalogue.
Fastening as needed from the side or bottom of the profile.
The railing is also suitable for use as security railing during construction. In this case, instead of glass panels, plywood boards must be installed which can easily be replaced by glass panels at the end of construction.
- Loading capacity of the railing up to 1.5 kN/m
- Profile dimensions 60 × 110 mm
- Aesthetic surface finish: brushed stainless steel effect
- Profile-milled mounting holes in spacing of 200 mm
- The standard length of the profiles is 3000 mm
- Glass thickness (mm): 10; 12; 13.5; 17.5; 19.5; 21.5
- Fast glass fastening with plastic wedges and a special tool
- The profile is also available bent
- Aluminum profile
- Glass support rubber seal
- Two-component plastic wedge
- Rubber seal covering the wedges
Bottom mounting system GP1
Required mounting accessories
- Chemical anchor + M12 threaded bolt (strength 8.8)
- M12 wedge anchor
Side mount system GP2
Required space of attaching profile
- 0.5 kN/m railing – 400 mm
- 1 kN/m railing – 200 mm
- 1.5 kN/m railing – 200 mm
Selection of handrails
Handrails on the side
Handrails on top
Strip on top
LL glass railing profile
Advantages of the LL70 railing system:
- basically unlimited life
- corrosion proof and weatherproof
- resistant to temperature changes from -50 ° to 80 °
- maintenance free
Technical specifications of LL70:
30 x 70mm square profile is used for the post. Handrail width 75 – 200mm (depending on the type of handrail)
We use 100% aluminum profiles according to the requirements of EN-AW 6060-T6 (GOST AD31) painted with powder paint according to RAL catalogue and pre-treated according to GSB requirements. All this will ensure the life of the profiles for long years
Can be mounted both on the balcony and the front edge of the balcony.
Laminated glass, which meets safety requirements 1B1 (old F2), is used as a balcony railing glass. The laminated glass 44.2 and 55.2 (hardened or not) are suitable for the glass profiles provided. The width of the glasses is usually equal to the spacing between the posts between 800 and 1200mm
Types of LL70
Dwelling stair railings